Supported coding options

BMW 3 Series, M3
F30, F31, F34, F35, F80
  • Checkbox acoustic pedestrian protection

    Enable/disable the checkbox in the settings in the iDrive system to turn the acoustic pedestrian protection on or off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Acoustical lock/unlock confirmation

    Enable/disable the acoustical confirmation when the car is locked/unlocked.

    Values:
    • Active
    • Not active
    Requirements:
    • “Anti-theft alarm system” CANS2 or “Roof Function Center” FZD__07 control unit
  • Checkbox acoustical lock confirmation

    Enable/disable the checkbox in the settings for doors/keys in the iDrive system to enable/disable the acoustical lock confirmation. If the checkbox in the iDrive system does not allow selection, please check if “Acoustical lock/unlock confirmation” in the “Roof Function Center” control unit is set to “Active“ also. Please note that the car has to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Confirmation sound duration

    The duration of the confirmation sound that is played when locking/unlocking the car.

    Values:
    • Short
    • Normal
    • Long
    • Very long
    Requirements:
    • “Anti-theft alarm system” CANS2 or “Roof Function Center” FZD__07 control unit
  • Confirmation sound frequency

    The frequency of the confirmation sound that is played when locking/unlocking the car.

    Values:
    Requirements:
    • “Anti-theft alarm system” CANS2 control unit
  • Confirmation sound frequency

    The frequency of the confirmation sound that is played when locking/unlocking the car.

    Values:
    • Low
    • Normal
    • High
    Requirements:
    • “Roof Function Center” FZD__07 control unit
  • Confirmation sound volume

    The volume of the confirmation sound that is played when locking/unlocking the car.

    Values:
    • Low
    • Normal
    • High
    • Very high
    Requirements:
    • “Anti-theft alarm system” CANS2 or “Roof Function Center” FZD__07 control unit
  • Active Cruise Control default distance

    The default distance level of the Active Cruise Control on activation.

    Values:
    • Level 1
    • Level 2
    • Level 3
    • Level 4
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • Active Rear Spoiler extension speed

    The speed at which the Active Rear Spoiler is extended.

    Values:
    • 60 km/h
    • 70 km/h
    • 80 km/h
    • 90 km/h
    • 100 km/h
    • 110 km/h
    Requirements:
    • “Tailgate Function Module” HKFM control unit
  • Active Rear Spoiler retraction speed

    The speed at which the Active Rear Spoiler is retracted.

    Values:
    • 50 km/h
    • 60 km/h
    • 70 km/h
    • 80 km/h
    Requirements:
    • “Tailgate Function Module” HKFM control unit
  • Active Sound Design deactivation

    Deactivate the Active Sound Design. Use a backup to revert this coding once it has been applied.

    Values:
    • Deactivated
    Requirements:
    • “Active Sound Design” ASD_01 control unit
  • Air circulation setting memory

    Enable/disable storing of the air circulation setting. If this function is active, the last used air circulation setting will be restored during the next start of the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA01 or “Air Conditioning” IHKA_VA02 control unit
  • Air conditioning on in AUTO mode

    Enable/disable the automatic activation of the air conditioning when the AUTO mode is turned on.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA01 or “Air Conditioning” IHKA_VA02 control unit
  • Air conditioning setting memory

    Enable/disable storing of the air conditioning setting. If this function is active, the last used air conditioning setting will be restored during the next start of the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA01 or “Air Conditioning” IHKA_VA02 control unit
  • Automatic Air Recirculation

    Enable/disable the Automatic Air Recirculation function.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Display color change

    Enable/disable the color change of the display from white to orange.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Alarm sound

    The alarm sound that is played when the alarm is triggered.

    Values:
    • Alarm sound Europe
    • Alarm sound Great Britain
    • Alarm sound USA
    Requirements:
    • “Anti-theft alarm system” CANS2 or “Roof Function Center” FZD__07 control unit
  • Interior motion detection

    Enable/disable the interior motion detection of the alarm system. Please note that this function requires the car to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Anti-theft alarm system” CANS2 control unit
  • OBD alarm

    The alarm is triggered when the vehicle is locked and communication via the OBD port is detected. Please note that this function requires the car to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Anti-theft alarm system” CANS2 control unit
  • Ambient lighting brightness

    The brightness of the ambient lighting.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Ambient lighting brightness decoupling from instrument cluster

    Enable/disable the decoupling of the brightness of the ambient lighting from the brightness of the instrument cluster.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Angel Eyes brightness

    The brightness of the Angel Eyes with low beam or parking lights. Use a backup to revert this coding once it has been applied. Please note that this coding has to be carried out for both headlights (left and right) separately.

    Values:
    • 100%
    Requirements:
    • “Front Light Electronics” FLE_02 control unit
  • Angel Eyes brightness low beam

    The brightness of the Angel Eyes with low beam. Please note that this coding has to be carried out for both headlights (left and right) separately.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Headlight Driver Module left” TMS_03 or “Headlight Driver Module right” TMS_03 control unit
  • Angel Eyes brightness low beam

    The brightness of the Angel Eyes with low beam.

    Values:
    • 8%
    • 10%
    • 12%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Angel Eyes brightness parking lights

    The brightness of the Angel Eyes with parking lights. Please note that this coding has to be carried out for both headlights (left and right) separately.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Headlight Driver Module left” TMS_03 or “Headlight Driver Module right” TMS_03 control unit
  • Angel Eyes brightness parking lights

    The brightness of the Angel Eyes with parking lights.

    Values:
    • 8%
    • 10%
    • 12%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Bluetooth audio streaming

    This coding enables wireless audio streaming via Bluetooth. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Bluetooth audio streaming (1 of 2)

    This coding enables wireless audio streaming via Bluetooth. Please note that for this function, “Bluetooth audio streaming (2 of 2)“ must also be activated in the “Combox“ control unit. If there is no “Combox“ installed in your car, Bluetooth audio streaming is not possible unfortunately. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_CIC control unit
  • Bluetooth audio streaming (2 of 2)

    This coding enables wireless audio streaming via Bluetooth. Please note that for this function, “Bluetooth audio streaming (1 of 2)“ must also be activated in the “Headunit“ control unit. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Combox” Combox_Media control unit
  • Maximum volume at start-up

    The maximum volume that is saved when the iDrive system is shut off and restored automatically on the next start-up.

    Values:
    • 10%
    • 20%
    • 25%
    • 30%
    • 40%
    • 50%
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Ringtone

    The ringtone that is used in case of an incoming call.

    Values:
    • Ringtone 1
    • Ringtone 2
    • Ringtone 3
    • Smartphone ringtone
    Requirements:
    • “Combox” Combox_Media control unit
  • Ringtone

    The ringtone that is used in case of an incoming call.

    Values:
    • BMW i ringtone
    • BMW ringtone
    • Mini ringtone
    • Smartphone ringtone
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Shut off iDrive system when driver door is opened

    Enable/disable the automatic shut-off of the iDrive system when the driver door is opened.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Warning chime

    The warning chime that sounds when a warning is displayed in the car.

    Values:
    • BMW i warning chime
    • BMW warning chime
    • Mini warning chime
    • Rolls Royce warning chime
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Auto Start Stop function in ECO mode

    Enable/disable the automatic activation of the Auto Start Stop function in ECO PRO driving mode.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Auto Start Stop function memory

    Save the last used Auto Start Stop function setting for the next start of the car. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Auto Start Stop function off by default

    Set the Auto Start Stop function to off by default when the car is started. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Battery type

    The type and capacity of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.

    Values:
    • 20 Ah
    • 40 Ah AGM
    • 46 Ah
    • 55 Ah
    • 70 Ah
    • 70 Ah AGM
    • 80 Ah
    • 80 Ah AGM
    • 90 Ah
    • 90 Ah AGM
    • 105 Ah AGM
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Blind spot detection activation speed

    The speed at which the blind spot detection system is activated.

    Values:
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 50 km/h
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • Brake Force Display activation brake force

    The brake deceleration at which the Brake Force Display is activated.

    Values:
    • Weak braking (5 m/s²)
    • Medium braking (7 m/s²)
    • Hard braking (8 m/s²)
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Brake Force Display activation speed

    The speed at which the Brake Force Display is activated.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Brake Force Display flashing frequency

    The flashing frequency of the Brake Force Display.

    Values:
    • 3 times per second
    • 5 times per second
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • Brake Force Display lights

    The lights used for the Brake Force Display.

    Values:
    • Brake lights
    • Not active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • Brake Force Display type

    The type of the Brake Force Display. The Brake Force Display is activated during hard braking to warn the following traffic. Please note that you have to set “Brake Force Display lights” to “Brake lights” in the “Rear Electronic Module” control unit additionally.

    Values:
    • Area enlargement
    • Flashing
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • CarPlay fullscreen mode

    Show CarPlay in full screen mode. Important: This coding only works with the iDrive software versions “NBTevo_X“ and “NBTevo_Y“. You can easily check for yourself which software version is currently installed in your vehicle. To do this, navigate to the version info in the iDrive system in your vehicle (Navigation > Settings > Position and version > Version information). If you can see “NBTevo_X“ or “NBTevo_Y“ here, then full screen mode will work. If you see “NBTevo_N“, “NBTevo_O“, “NBTevo_P“, “NBTevo_Q“, “NBTevo_R“, “NBTevo_S“, “NBTevo_U“, “NBTEvo_V“ or “NBTEvo_W“ instead, then full screen mode can not be enabled with BimmerCode unfortunately. In this case, an update of the i-level from a BMW service partner is required first.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Convenient closing

    Enable/disable the convenient closing. During convenient closing the windows are closed and the power folding mirrors are folded in. To trigger convenient closing the lock button on the remote control has to be pressed and held. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient closing delay

    The delay for the convenient closing before the windows are closed.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient closing delay front windows

    The delay at which the front windows are closed during convenient closing.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient closing delay sunroof

    The delay as of with the sunroof is closed during convenient closing.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 3.5 seconds
    • No delay
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient closing with Comfort Access

    Enable/disable the convenient closing with the Comfort Access. For convenient closing with the Comfort Access the door handle has to be touched and held at the ribbed surface. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient closing with remote control

    Enable/disable the convenient closing with the remote control. For convenient closing with the remote control, the lock button has to be pressed and held. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient opening

    Enable/disable the convenient opening. During convenient opening the windows are opened and the power folding mirrors are unfolded. For a convenient opening the unlock button on the remote control has to be pressed and held. When using Comfort Access, the door handle has to be gripped and held.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient opening delay

    The delay for the convenient opening before the windows are opened.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 2 seconds
    • 2.5 seconds
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient opening delay rear windows

    The delay at which the rear windows are opened during convenient opening.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient opening delay sunroof

    The delay as of with the sunroof is opened during convenient opening.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 3.5 seconds
    • No delay
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Convenient opening with remote control

    Enable/disable the convenient opening with the remote control. For convenient opening with the remote control, the unlock button has to be pressed and held.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Checkbox daytime running light

    Enable/disable the checkbox in the lighting settings in the iDrive system to turn the daytime running light on or off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Daytime running light brightness

    The brightness of the daytime running light.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Daytime running light mode

    The daytime running light mode.

    Values:
    • Active
    • Active also with parking lights
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Daytime running light tail lights inner part

    Enable/disable the inner part of the tail lights with the daytime running light.

    Values:
    • Active
    • Not active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • Daytime running light tail lights outer part

    Enable/disable the outer part of the tail lights with the daytime running light.

    Values:
    • Active
    • Not active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • Display full text messages

    Enable the full display of text messages while driving. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Pressure and temperature in tyre pressure monitor

    Enable/disable the pressure and temperature in the tyre pressure monitor in the iDrive system. Please note that the car has to be equipped with the required sensors. This option affects the display only and it is not possible to completely deactivate the tire pressure monitoring in the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC control unit
  • Rear view camera zoom

    Enable/disable the rear view camera zoom to the trailer hitch.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Service history

    Enable/disable the service history in the iDrive system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Start animation

    The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.

    Values:
    • ALPINA
    • BMW 1
    • BMW 2
    • BMW i
    • Christmas
    • Connected Drive 1
    • Connected Drive 2
    • M variant 1
    • MINI variant 1
    • Rolls Royce
    Requirements:
    • “Headunit” HU_NBT control unit
  • Start animation

    The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.

    Values:
    • ALPINA
    • BMW i
    • Connected Drive
    • M variant 1
    • M variant 2
    • MINI John Cooper Works
    • MINI variant 1
    • MINI variant 2
    • Rolls Royce
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Start screen

    The type of start screen that is displayed when the head unit starts up.

    Values:
    • Animation
    • Welcome screen
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Tire pressure control

    The displayed values of the tire pressure control in the iDrive system. Please note that the car has to be equipped with the required sensors to make this work.

    Values:
    • Display pressure only
    • Display temperature and pressure
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Volume popup

    Enable/disable the volume popup that is displayed when the volume is changed.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Average values reset

    The average speed and consumption is reset after the set time automatically.

    Values:
    • After 4 hours
    • After 8 hours
    • After every ride
    • Never
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS or “Instrument Cluster” KOMBI L6 BO or “Instrument Cluster” KOMBI_CT_RD1 control unit
  • Date in board computer

    Enable/disable the display of the date in the board computer. Please toggle the displayed information in the board computer with the button in the turn signal lever until the specific display appears.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS control unit
  • Digital speed in board computer

    Enable/disable the display of the digital speed in the board computer. Please toggle the displayed information in the board computer with the button in the turn signal lever until the specific display appears.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS or “Instrument Cluster” KOMBI L6 BO or “Instrument Cluster” KOMBI_CT_RD1 control unit
  • Empty menu item in board computer

    Enable/disable the empty menu item in the board computer.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS or “Instrument Cluster” KOMBI L6 BO or “Instrument Cluster” KOMBI_CT_RD1 control unit
  • Fuel consumption display maximum value

    The maximum value of the fuel consumption display.

    Values:
    • 20 l/100km
    • 30 l/100km
    Requirements:
    • “Instrument Cluster” KOMBI_CT_RD1 control unit
  • M Performance logo

    The model-specific M Performance logo that is displayed in the bottom right in the instrument cluster.

    Values:
    • Not active
    • 135i
    • 140i
    • 235i
    • 240i
    • 340i
    • 50d
    • 550d
    • Plugin Hybrid Electric Vehicle
    • X2 M40i
    Requirements:
    • “Instrument Cluster” KOMBI_CT_RD1 control unit
  • Horn signal when locking the car with engine running

    Enable/disable the horn signal that sounds when locking the car with the engine running.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Lock after pulling away

    Enable/disable the “Lock after pulling away“ checkbox in the settings in the iDrive system in the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Time until automatic lock

    The car is locked automatically again if it has been unlocked and no door has been opened within the set time.

    Values:
    • 10 seconds
    • 30 seconds
    • 1 minute
    • 2 minutes
    • 5 minutes
    • 10 minutes
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Unlock doors automatically

    Enable/disable the automatic unlock of the doors when the ignition is turned off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Window lifter interruption when opening a door

    Enable/disable the window lifter interruption when a door is opened.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • SPORT driving mode configurable (1 of 2)

    Activates the “Configure SPORT” option in the iDrive system, which allows you to configure the SPORT driving mode indiviudally. Please note that “SPORT mode configurable (2 of 2)” in the “Headunit” control unit has to enabled additionally. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • SPORT driving mode configurable (2 of 2)

    Activates the “Configure SPORT” option in the iDrive system, which allows you to configure the SPORT driving mode indiviudally. Please note that “SPORT mode configurable (1 of 2)” in the “Integrated Chassis Management” control unit has to enabled additionally. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • SPORT+ driving mode (1 of 2)

    Add the SPORT+ driving mode for cars that do not have this option by factory. Please note that “SPORT+ driving mode (2 of 2)” in the “Instrument Cluster” control unit has to be enabled additionally. Use a backup to revert this coding once it has been applied. Do not use this if you car already has the SPORT+ driving mode!

    Values:
    • Active
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • SPORT+ driving mode (2 of 2)

    Add the SPORT+ driving mode for cars that do not have this option by factory. Please note that “SPORT+ driving mode (1 of 2)” in the “Integrated Chassis Management” control unit has to enabled additionally. Use a backup to revert this coding once it has been applied. Do not use this if you car already has the SPORT+ driving mode!

    Values:
    • Active
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS or “Instrument Cluster” KOMBI L6 BO control unit
  • Start in ECO mode

    Enable/disable the ECO driving mode as default.

    Values:
    • Active
    • Not active
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • Easy entry protection area

    The protection area limits the rearward travel of the seat when easy entry is activated.

    Values:
    • 0 mm
    • 10 mm
    • 20 mm
    • 30 mm
    • 40 mm
    • 50 mm
    • 60 mm
    • 70 mm
    • 80 mm
    • 90 mm
    • 100 mm
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Easy entry seat movement

    In order to make it easier to get in the car, the seat is automatically moved back when unlocked and then returns to its original position when the ignition is switched on. Please note that the car has to be equipped with electrically adjustable seats with memory function.

    Values:
    • Active
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Easy entry seat travel

    The seat travel of the seat when easy entry is activated.

    Values:
    • 10 mm
    • 20 mm
    • 30 mm
    • 40 mm
    • 50 mm
    • 60 mm
    • 70 mm
    • 80 mm
    • 90 mm
    • 100 mm
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Low fuel warning 1

    The remaining range at which the permanent low fuel warning is displayed.

    Values:
    • 10 kilometers
    • 10 miles
    • 20 kilometers
    • 20 miles
    • 30 kilometers
    • 30 miles
    • 40 kilometers
    • 50 kilometers
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS or “Instrument Cluster” KOMBI L6 BO or “Instrument Cluster” KOMBI_CT_RD1 control unit
  • Low fuel warning 2

    The remaining range at which the temporary low fuel warning is displayed.

    Values:
    • 40 miles
    • 50 kilometers
    • 50 miles
    • 60 kilometers
    • 70 kilometers
    • 80 kilometers
    • 90 kilometers
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L7_BASIS or “Instrument Cluster” KOMBI L6 BO or “Instrument Cluster” KOMBI_CT_RD1 control unit
  • HUD music lists

    Enable/disable music lists in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • HUD phone book

    Enable/disable the telephone book in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • HUD telephone list

    Enable/disable the telephone list in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • HUD voice input

    Enabled/disable voice input display in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • Headlight cleaning blocking time

    The blocking time between headlight cleaning activations.

    Values:
    • 1 minute
    • 2 minutes
    • 3 minutes
    • 4 minutes
    • 5 minutes
    • 6 minutes
    • 7 minutes
    • 8 minutes
    • 9 minutes
    • 10 minutes
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Headlight cleaning pause between injection pulses

    The pause between the injection pulses of the headlight cleaning system.

    Values:
    • 200 ms
    • 400 ms
    • 600 ms
    • 800 ms
    • 1000 ms
    • 1200 ms
    • 1400 ms
    • 1600 ms
    • 1800 ms
    • 2000 ms
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Headlight cleaning system deactivation speed threshold

    The deactivation speed threshold at which the headlight cleaning system is deactivated.

    Values:
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    • 60 km/h
    • 70 km/h
    • 80 km/h
    • 90 km/h
    • 100 km/h
    • 110 km/h
    • 120 km/h
    • 130 km/h
    • 140 km/h
    • 150 km/h
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Headlight washers

    Activate/deactivate the headlight washers.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Number of washing operations for headlight cleaning

    The number of washing operations at which the headlight cleaning is turned on.

    Values:
    • 1 operation
    • 5 operations
    • 10 operations
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Number of water injection pulses during headlight cleaning

    The number of water injection pulses during headlight cleaning.

    Values:
    • 1 time
    • 2 times
    • 3 times
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Water injection duration for headlight cleaning

    The duration of the water injection pulses of the headlight cleaning system.

    Values:
    • 200 ms
    • 400 ms
    • 600 ms
    • 800 ms
    • 1000 ms
    • 1200 ms
    • 1400 ms
    • 1600 ms
    • 1800 ms
    • 2000 ms
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion Brake Force Display

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion bi-xenon

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion brake light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion center brake light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion daytime running lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion fog lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion front turn signal

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion high beam

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion inner tail lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion license plate light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion low beam

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion outer tail lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion position lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion rear fog light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion rear turn signals

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion reversing light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • LED conversion side turn signal

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • LED conversion sidemarkers

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Cornering lights activation

    Activate the cornering lights. To make this work, the car has to be equipped with fog lights. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Cornering lights deactivation

    Deactivate the factory installed cornering lights. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Door handle lights when reverse gear is engaged

    Enable/disable the automatic activation of the lights in the door handles when the reverse gear is engaged.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Fog lights deactivation

    Deactivation of the fog lights is necessary if the fog lights are removed, otherwise error messages will be displayed in the vehicle.

    Values:
    • Fog lights deactivated
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Fog lights off with high beam

    Enable/disable the automatic switch-off of the fog lights when the high beam is turned on.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Fog lights with parking lights

    Allows the fog lights to be turned on with parking lights.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Hazard warning signal after emergency braking

    The hazard warning signal is activated automatically after an emergency braking.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rain-light-sensor sensitivity

    The sensitivity of the rain-light-sensor that affects the automatic wiper and light activation.

    Values:
    • Insensitive
    • Normal
    • Sensititve
    • Very sensitive
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Sidemarkers

    Disable the sidemarkers in US cars. Use a backup to revert this coding once it has been applied. Please note that this coding has to be carried out for both headlights (left and right) separately.

    Values:
    • Deactivated
    Requirements:
    • “Headlight Driver Module left” TMS_03 or “Headlight Driver Module right” TMS_03 control unit
  • Automatic mirror tilt

    Enable/disable the automatic mirror tilt for the right mirror, when the reverse gear is engaged. Please note that your car has to be equipped with power folding mirrors. Make sure the button in the door for selecting the mirror is set to the driver side also.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Automatic mirror tilt value

    The tilt value of the right mirror, when the reverse gear is engaged.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Fold mirrors with convenient closing

    Enable/disable the folding of the mirrors when using convenient closing. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Fold/unfold mirrors automatically

    The mirrors are folded automatically when the car is locked with the remote control or Comfort Access and unfolded when the car is unlocked. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Mirror folding speed threshold

    The maximum speed at which the mirrors can be folded.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Mirror unfolding speed threshold

    The speed at which the mirrors are unfolded automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Unfold mirrors with convenient opening

    Enable/disable the unfolding of the mirrors when using convenient opening.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Activate PDC when rolling backwards

    Enable/disable the automatic activation of the PDC when the car starts rolling backwards.

    Values:
    • Active
    • Not active
    Requirements:
    • “Park Distance Control” PMA_PDC or “Rear Electronic Module” REM_01 control unit
  • PDC deactivation during trailer operation

    The PDC is deactivated automatically during trailer operation.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • PDC distance switch-off threshold

    The driven distance after the PDC is turned off automatically.

    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    Requirements:
    • “Park Distance Control” PMA_PDC or “Rear Electronic Module” REM_01 control unit
  • PDC speed switch-off threshold

    The speed at which the PDC is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” PMA_PDC or “Rear Electronic Module” REM_01 control unit
  • Speed switch-off threshold for visual and acoustic PDC warnings

    The speed at which the visual and acoustic PDC warnings are turned off.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • Rear view camera distance switch-off threshold

    The driven distance after the rear view camera is turned off automatically.

    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    Requirements:
    • “Park Distance Control” PMA_PDC or “Rear Electronic Module” REM_01 control unit
  • Rear view camera speed switch-off threshold

    The speed at which the rear view camera is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” PMA_PDC or “Rear Electronic Module” REM_01 control unit
  • HiFi loudspeaker system

    Coding for a retrofitted HiFi loudspeaker system. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • LCI tail lights

    Coding of all relevant functions for retrofitted LCI tail lights. Please note that the wiring of the tail lights may also have to be adapted. You can find information on this in the manufacturer's installation instructions.

    Values:
    • Active
    Requirements:
    • “Rear Electronic Module” REM_01 control unit
  • Steering wheel with paddles

    Enable/disable the paddles for a retrofitted steering wheel.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Front backrests temperature level 1

    The temperature of the front backrests for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    • 35 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Front backrests temperature level 2

    The temperature of the front backrests for seat heating level 2.

    Values:
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    • 41 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Front backrests temperature level 3

    The temperature of the front backrests for seat heating level 3.

    Values:
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    • 47 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Front seats temperature level 1

    The temperature of the front seats for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Front seats temperature level 2

    The temperature of the front seats for seat heating level 2.

    Values:
    • 35 °C
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Front seats temperature level 3

    The temperature of the front seats for seat heating level 3.

    Values:
    • 41 °C
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rear backrests temperature level 1

    The temperature of the rear backrests for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    • 35 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rear backrests temperature level 2

    The temperature of the rear backrests for seat heating level 2.

    Values:
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    • 41 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rear backrests temperature level 3

    The temperature of the rear backrests for seat heating level 3.

    Values:
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    • 47 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rear seats temperature level 1

    The temperature of the rear seats for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rear seats temperature level 2

    The temperature of the rear seats for seat heating level 2.

    Values:
    • 35 °C
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Rear seats temperature level 3

    The temperature of the rear seats for seat heating level 3.

    Values:
    • 41 °C
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Seat heating/cooling setting memory

    The memory duration of the seat heating/cooling settings.

    Values:
    • 15 minutes
    • 24 hours
    • Do not save
    • Unlimited
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Initial seat belt reminder after start

    Activate/deactivate the initial acoustic seat belt reminder after the car is started.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt indicator driver seat

    Activate/deactivate the seat belt indicator in the instrument cluster for the driver seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt indicator passenger seat

    Activate/deactivate the seat belt indicator in the instrument cluster for the passenger seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt indicator rear seats

    Activate/deactivate the seat belt indicator in the instrument cluster for the rear seats.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder distance

    Driven distance at which th seat belt reminder is activated.

    Values:
    • 50 m
    • 100 m
    • 200 m
    • 500 m
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder driver seat

    Activate/deactivate the acoustic and visual seat belt reminder for the driver seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder duration

    Duration at which the seat belt reminder stays active.

    Values:
    • 5 seconds
    • 10 seconds
    • 15 seconds
    • 20 seconds
    • 30 seconds
    • 45 seconds
    • 60 seconds
    • 90 seconds
    • 100 seconds
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder passenger seat

    Activate/deactivate the acoustic and visual seat belt reminder for the passenger seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder speed

    Speed at which th seat belt reminder is activated.

    Values:
    • 8 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4B or “Advanced Crash Safety Module” ACSM_4C control unit
  • Activation speed threshold side view camera

    The speed at which the side view camera can be activated.

    Values:
    • 15 km/h
    • No speed limit
    Requirements:
    • “Allround View Camera” TRSVC control unit
  • Deactivation speed threshold side view camera

    The speed at which the side view camera is deactivated.

    Values:
    • 15 km/h
    • No speed limit
    Requirements:
    • “Allround View Camera” TRSVC control unit
  • Sport displays

    Enable/disable the Sport displays in the iDrive system. Please note that in some cars the engine control unit does not transmit the required values to the headunit and in this case the Sport displays will be displayed but remain functionless.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Sport displays color

    The color of the Sport displays in the iDrive system.

    Values:
    • Orange
    • Red
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Steering wheel heating memory

    The activation of the steering wheel heating is saved and restored the next time the vehicle is started.

    Values:
    • 15 minutes
    • 24 hours
    • Do not save
    • Unlimited
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Boot lid opening delay

    The delay when opening the boot lid with the remote control. This value can be increased to prevent accidental openings of the boot lid.

    Values:
    • 0.5 seconds
    • 1 second
    • 5 seconds
    • 10 seconds
    • No delay
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Close tailgate with button in the interior

    Enable/disable closing the tailgate with the button in the interior.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKL_III or “Tailgate Function Module” HKFM control unit
  • Close tailgate with button in the interior without long press

    Enable/disable the closing of the tailgate with the button in the interior without a long press.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Close tailgate with remote control

    Enable/disable closing of the tailgate with the remote control.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKL_III or “Tailgate Function Module” HKFM control unit
  • Close tailgate with remote without long press

    Enable/disable closing the tailgate with the remote control without a long press.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKL_III or “Tailgate Function Module” HKFM control unit
  • Close tailgate with the remote control without long press

    Enable/disable closing the tailgate without a long press of the button on the remote control.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Tailgate function remote control

    The tailgate function that is triggered when the button on the remote is pressed.

    Values:
    • Open
    • Open and close
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Tailgate function when pulling the button in the interior

    The tailgate function that is triggered when the button in the interior is pulled up.

    Values:
    • Close
    • Deactivated
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Tailgate function when pushing the button in the interior

    The tailgate function that is triggered when the button in the interior is pushed down.

    Values:
    • Deactivated
    • Open
    • Open and close
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Warning sound when closing the tailgate with remote control

    A warning signal sounds when the tailgate is closed with the remote control.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Warning sound when closing the tailgate with the button in the interior

    A warning signal sounds when the tailgate is closed with the button in the interior.

    Values:
    • Active
    • Not active
    Requirements:
    • “Tailgate Function Module” HKFM2 control unit
  • Sport Automatic Transmission

    Enable/disable the Sport Automatic Transmission.

    Values:
    • Active
    • Not active
    Requirements:
    • “Electronic Transmission Control” GKEB23 control unit
  • Turn signals flashing on locking

    Number of turn signal flashes when locking the car.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • Off
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Turn signals flashing on unlocking

    Number of turn signal flashes when unlocking the car.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • Off
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • US sidemarker brightness

    The brightness of the US sidemarkers.

    Values:
    • Off
    • Very low
    • Low
    • Medium
    • Relatively high
    • High
    • Very high
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • US sidemarker light function

    The light function where the US sidemarkers are turned on.

    Values:
    • Standing lights
    • Daytime running light
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • US sidemarkers

    Enable/disable the US style sidemarkers using the turn signals or separate lights.

    Values:
    • Mirror turn signals
    • Off
    • Separate lights
    • Turn signals
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Additional video codecs and formats

    Activate additional video codecs and formats (Ogg, Xvid and VCD). Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Video in motion

    Activate video in motion. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Video in motion

    Enable video in motion. Please note the instructions displayed after coding.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Video via USB

    Enable video playback from USB storage media. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Welcome Light activation

    The position of the light switch at which the Welcome Light is activated.

    Values:
    • Light switch on auto
    • Light switch on auto or 2
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Light in darkness only

    Enable/disable the activation of the Welcome light in darkness only.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Light lighting duration

    The lighting duration of the Welcome Light.

    Values:
    • 5 seconds
    • 10 seconds
    • 15 seconds
    • 20 seconds
    • 30 seconds
    • 45 seconds
    • 60 seconds
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights brightness

    The brightness of the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights central turn signals

    The central turn signals are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights cornerning lights

    The cornerning lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights daytime running light

    The daytime running light is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights design lights

    The design lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights fog lights

    The fog lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights front turn signals

    The front turn signals are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights high beam 1

    The high beam 1 is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights high beam 2

    The high beam 2 is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights low beam

    The low beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights parking lights

    The daytime parking lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Welcome Lights sidemarkers

    The sidemarkers are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Automatic rear wiper in reverse

    Enable/disable the automatic rear wiper activation when reverse gear is engaged.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Wipe cycles after front washing

    The number of wipe cycles after front washing

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Wipe cycles after rear washing

    The number of wipe cycles after rear washing.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
  • Wiper level switch back when stationary

    Enable/disable the automatic switch back of the wiper level when the car becomes stationary.

    Values:
    • Active
    • Not active
    Requirements:
    • “Front Electronic Module” FEM_01 control unit
We use cookies to optimize the website and user-experience. Learn more in our Privacy Policy.